Clubjazz - Honda Jazz & HR-V Forums

Honda Jazz Forums => Honda Jazz Mk2 2008-2015 => Topic started by: guest5247 on December 28, 2015, 05:15:30 PM

Title: Drivers Headrest.
Post by: guest5247 on December 28, 2015, 05:15:30 PM
Had my Jazz a few weeks now,  my headrest does seem to be at a farely forward angle.

So i need my seat quite laid back to stop my head from being pushed forward , i prefer to sit a little more upright but if i do this the headrest actually stops me from putting my head back.

Have to admit its comfortable as it is,  but I just prefer sitting more upright.



Title: Re: Drivers Headrest.
Post by: trebor1652 on December 28, 2015, 05:54:56 PM
I had the same problem took quite a bit of fiddling with different settings to get it right.

Sent from my XT1039 using Tapatalk

Title: Re: Drivers Headrest.
Post by: stiggysawdust on December 30, 2015, 02:24:34 PM
I had same problem which I solved by removing the headrests and straightening the bars a touch. First try wasn't enough but after another go they were perfect.
Title: Re: Drivers Headrest.
Post by: Pine on December 31, 2015, 07:34:56 PM
Its a problem that has been raised on this forum before.

I complained about it to Honda Customer Services, whether my comments were passed on I could not say.  Initially I took the headrests out and replaced them with a set from a GD model 2005, but I felt they were to far back. I put the originals back and gradually reclined the backrest until it was acceptable.  You get used to it although I would have preferred to sit more upright.

When I changed my car I tried a Civic but could not get comfortable in that seat either. I ended up buying a Ford Fiesta.
Title: Re: Drivers Headrest.
Post by: applicationcen on December 31, 2015, 07:59:40 PM
It is not just the Jazz - A lot of cars complying to a specific Crash / Whip Lash mitigation standard all cause the head to be tipped forward for many driver body shapes.

It is not recommended officially - but the easiest way to adapt it is put it in a vice and gently nudge it back.

I am going to do this.
Title: Re: Drivers Headrest.
Post by: John Ratsey on December 31, 2015, 08:50:37 PM
Honda must have taken note: This problem is less on the Mk 3 Jazz which has limited tilt adjustment for the headrests by pushing a button on the side. It might be interesting to investigate whether the headrests are interchangeable, not that Mk 3 headrests will be easy to find in the scrap yards.
Title: Re: Drivers Headrest.
Post by: culzean on January 01, 2016, 10:47:58 AM
It is not just the Jazz - A lot of cars complying to a specific Crash / Whip Lash mitigation standard all cause the head to be tipped forward for many driver body shapes.

It is not recommended officially - but the easiest way to adapt it is put it in a vice and gently nudge it back.

I am going to do this.

This problem  has been around for years and if you search most car forums there will be complaints about this (even luxury cars) - apparently car makers can gain points in crash tests by reducing gap between rear of drivers head and the headrest,  and have pushed the headrest forward of the back of seat to do this,  if you have seat back at more of an angle from vertical and 'slouch' when you drive (and wear a baseball hat backwards) apparently it is more comfortable, but for the ones of us who like to sit more upright it is literally a 'pain in the neck'.  Poor old car makers have to cater for every driver from 4'6"  to 7'  tall,  from 6 stone to 30 stone and every conceivable seating position preference,  it is not an easy job and they invest large sums of money in trying to get it right and also satisfy car crash test legislation from different countries.

They are only allowed to have limited adjustments so that people cannot adjust their headrests into what legislators consider 'unsafe' positions.

http://ergorisk.com/new-vehicle-head-restraints-are-uncomfortable/ (http://ergorisk.com/new-vehicle-head-restraints-are-uncomfortable/)

https://www.reddit.com/r/mazda/comments/2fdas8/the_mazda3_headrest_is_uncomfortable/ (https://www.reddit.com/r/mazda/comments/2fdas8/the_mazda3_headrest_is_uncomfortable/)

Title: Re: Drivers Headrest.
Post by: guest5247 on January 01, 2016, 11:29:17 AM
Crikey , so many replies.

Thank you all  :)

Had no idea this was a problem.

I had a 2002 Toyota Rav4 before the Jazz , had lovely upright seating but its 2nd turbo blew.

The jazz is amazingly versatile for a supermini , but i may end up getting those headrest stems heated and eased backwards.

I have a steel fabricators nearby,  bit of oxy acetylene gently and ease them back a few dregrees. ;D



Title: Re: Drivers Headrest.
Post by: stiggysawdust on January 03, 2016, 02:00:18 PM
Crikey , so many replies.

Thank you all  :)

Had no idea this was a problem.

I had a 2002 Toyota Rav4 before the Jazz , had lovely upright seating but its 2nd turbo blew.

The jazz is amazingly versatile for a supermini , but i may end up getting those headrest stems heated and eased backwards.

I have a steel fabricators nearby,  bit of oxy acetylene gently and ease them back a few dregrees. ;D

They bend quite easily with a vice and short piece of tubeing. I didn't need any heat with mine. Very successful.
Title: Re: Drivers Headrest.
Post by: guest5247 on January 07, 2016, 01:44:08 PM
Crikey , so many replies.

Thank you all  :)

Had no idea this was a problem.

I had a 2002 Toyota Rav4 before the Jazz , had lovely upright seating but its 2nd turbo blew.

The jazz is amazingly versatile for a supermini , but i may end up getting those headrest stems heated and eased backwards.

I have a steel fabricators nearby,  bit of oxy acetylene gently and ease them back a few dregrees. ;D

They bend quite easily with a vice and short piece of tubeing. I didn't need any heat with mine. Very successful.

Oh...ok , marvellous I'll give it a go at the weekend.

Thank you.
Title: Re: Drivers Headrest.
Post by: guest5247 on February 01, 2016, 07:52:06 PM
Well i complained to Honda about the headrests , they could do nothing!

So this evening I've cut very carefully with a junior hacksaw a birds beak out of the rear of the curve of each stem.

I've then bent the headrest back gently until the birds beak closed up  :D

I've now got upright headrests....yippeeee,  and comfort again  ;D

My car , my headrest,  my choice.

Happy days again.
Title: Re: Drivers Headrest.
Post by: culzean on February 01, 2016, 07:57:11 PM
Well i complained to Honda about the headrests , they could do nothing!

So this evening I've cut very carefully with a junior hacksaw a birds beak out of the rear of the curve of each stem.

I've then bent the headrest back gently until the birds beak closed up  :D

Could be nasty if you or a subsequent owner has a crash and the tubes break and cause serious puncturing injury to back of head or spine. 
Title: Re: Drivers Headrest.
Post by: guest5247 on February 01, 2016, 09:42:59 PM
Well i complained to Honda about the headrests , they could do nothing!

So this evening I've cut very carefully with a junior hacksaw a birds beak out of the rear of the curve of each stem.

I've then bent the headrest back gently until the birds beak closed up  :D

Could be nasty if you or a subsequent owner has a crash and the tubes break and cause serious puncturing injury to back of head or spine.

Yep....realise that , but I'm seriously fed up with sitting in discomfort day in day out >:( and tbh in my mind those head ' restraints ' are just  ridiculous at that angle.
Its only a 3mm birds beak so not to extreme , and the steel tube is seriously strong. Still took some serious strength to bend them  ;D
The passengers is absolutely fine !

So do something about it , ive bought a replacement off eBay for if i sell it.
Title: Re: Drivers Headrest.
Post by: guest5247 on February 01, 2016, 10:33:46 PM
Had another thought,  ill get them re welded to reinforce them shortly as I've got a steel fabricators locally and know them well  :)
Title: Re: Drivers Headrest.
Post by: guest5247 on February 15, 2016, 10:09:42 AM
Well , had headrest stems re welded this morning.

Now strong again.

All i have to do is a decent re chrome re spray myself, cost me a drink with a local steel fabricators whom I've known for 20 years.

[attachment deleted by admin]
Title: Re: Drivers Headrest.
Post by: guest1262 on February 15, 2016, 12:17:19 PM
I heard a BBC radio prog a few days ago Rambler about a driver having his car insurance voided because some of his car's parts were non-manufacturer originals - thus his car had been modified and he'd not mentioned this when taking out insurance. He knew nothing about them when he'd bought the car second-hand from a dealer  - who denied knowledge.

By the same way of thinking the changes to your headrest are a modification. This could create serious problems in the event of any insurance claim by you or a future owner. Take care.
Title: Re: Drivers Headrest.
Post by: guest5247 on February 15, 2016, 10:11:43 PM
I heard a BBC radio prog a few days ago Rambler about a driver having his car insurance voided because some of his car's parts were non-manufacturer originals - thus his car had been modified and he'd not mentioned this when taking out insurance. He knew nothing about them when he'd bought the car second-hand from a dealer  - who denied knowledge.

By the same way of thinking the changes to your headrest are a modification. This could create serious problems in the event of any insurance claim by you or a future owner. Take care.
I hear what you say , that's why I've purchased another one from ebay to replace mine when i sell.

And my current headrest is still the original, only mine is....comfortable for me ,no neck or back ache.

A head restraint is a head restraint, its in place doing its job. And its not an MOT failure.

Tbh...if a random person looked at my car now , you wouldn't tell the difference at a glance if you didn't know as the change is that discreet.

Thank you all for your concern though, really appreciated and taken aboard.




Title: Re: Drivers Headrest.
Post by: guest5247 on February 16, 2016, 12:13:15 PM
Just rang insurance, for my peace of mind.

Even emailed them the photo.

Its not an issue with them , if it doesn't affect power or braking performance its not classed as a problem.
But they have a note of it and the photo.
If I'd left the stems cut then yes , but now they're welded its fine.