Author Topic: How to deal with Aluminium corrosion  (Read 2477 times)

guest5079

  • Guest
How to deal with Aluminium corrosion
« on: April 24, 2017, 02:24:18 PM »
In preparation for a plug change. I did a bit of prelim on the removal of the 'Cowl Cover'. After taking off an inspection cover by the brake reservoir I saw that the wiper motor was covered in white pustules.  Now I believe this is corrosion. I did a Google search  but it was all technical way above my head and basically talking about spraying on two coats etc, I think it was aimed at production of aluminium parts and professional protection after manufacture.
Any suggestions on how to clean what I believe to be aluminium oxide off the parts and how to protect them after. Obviously it will have to be done insitu and not taken to a specialist, if I could find one less than mega miles away.
Thanks

VicW

  • Approved Member
  • *
  • Posts: 1441
  • Country: england
  • My Honda: 07 Plate Civic 1.8 i-Shift.
Re: How to deal with Aluminium corrosion
« Reply #1 on: April 24, 2017, 03:56:09 PM »
I doubt it's serious Neddy, it will probably brush off with a tooth brush.

Vic.

culzean

  • Approved Member
  • *
  • Posts: 8017
  • Country: england
Re: How to deal with Aluminium corrosion
« Reply #2 on: April 24, 2017, 04:49:52 PM »
I doubt it's serious Neddy, it will probably brush off with a tooth brush.

Vic.

Yeah unlike steel oxide (rust) aluminium oxide does not flake off it stays put and protects metal underneath (aluminium oxide is very hard, they make abrasive paper, metal cutting discs and grinding wheels out of it.  If you are worried spray WD40 (one of the few things its good for) or ACF-50 onto it.
« Last Edit: April 25, 2017, 09:22:45 AM by culzean »
Some people will only consider you an expert if they agree with your point of view or advice,  when you give them advice they don't like they consider you an idiot

guest5079

  • Topic Starter
  • Guest
Re: How to deal with Aluminium corrosion
« Reply #3 on: April 25, 2017, 08:57:15 AM »
Thank you both.  It is probably not as bad as it looked peering through a small aperture.
A soft brush and WD40 will be the order of the day when I do the plugs.
Many thanks

culzean

  • Approved Member
  • *
  • Posts: 8017
  • Country: england
Re: How to deal with Aluminium corrosion
« Reply #4 on: April 27, 2017, 08:46:02 PM »
Sometimes zinc or passivated zinc steel bodies are used for motors,  these can also develop a powdery white coating under certain circumstances,  try the motor with a magnet to see if it is aluminium or zinc coated steel - if zinc coated I would not clean it too vigorously and risk removing some of the zinc coating,  rather just wipe it over and use WD or other sticky coating to keep moisture away.
Some people will only consider you an expert if they agree with your point of view or advice,  when you give them advice they don't like they consider you an idiot

guest5079

  • Topic Starter
  • Guest
Re: How to deal with Aluminium corrosion
« Reply #5 on: April 28, 2017, 02:16:06 PM »
I only looked at it through the aperture by the brake fluid reservoir. It could be just the mounting bracket. Looking at the photograph on the ' DIY lower your GE8 Fit' which gives very clear instruction on 'Cowl' removal, the motor is hidden but appears as you say to be a pressing which of course will be plated.
When we get a nice warm day I shall attempt the plug change.
The WD40 does seem to be the answer.
Once again thanks for the info.

Tags:
 

Back to top